How to build a PAPRa m12 Battery Controller (April 2024)

How-To guide for building the Tetra PAPRa m12 battery controller (April 2024 version).

Quick Synopsis

The Tetra Powered Air Purified Respirator requires power to function, and the m12 battery controller provides that power for these models. The controller consists of internal circuitry, a potentiometer to adjust fan speeds, a cable to connect to the fan box, and a port for a Milwaulkee M12 Battery to be inserted.

This build differs from the v1 version in that it uses a custom-built circuitboard to remove many of the difficult steps of the build, add a battery charge indicator, and a separate power port for use in a car. If you cannot get the custom board, then please refer to the v1 version of this guide.

WARNING: we provide no warranty, implicit or explicit, that this device will work up to an N95 specification, when built outside of a facility rated to do so. The only way to truly test one of these devices using something like a Portacount under controlled conditions.

Parts Required

This build will require printed parts, purchased parts, and several tools. Here is a picture of all the components used in this build:

DSCF0364 X3

And the assembly diagram can be found here. Note that this assembly calls for version 0.7 of the board.

3D Printed Parts

These parts should be printed at 0.2 spacing:

Table 1. Table Printed Parts
PartQuantityMaterialSupports Required?STL File Location

Knob

1

PETG

No

Knob

Body One Piece (alternative part for Body + Light Panel)

1

Transparent PETG

No

Body One Piece

Plate

1

PETG

No

Plate

MOLLE Strap

1

PETG

No

MOLLE Strap

MOLLE Catch

1

PETG

No

MOLLE Catch

Body

1

PETG

No

Body

Lid

1

PETG

No

Lid

Lid

1

PETG

No

Lid

Light Panel

1

Transparent PETG

No

Light Panel

Bill Of Materials

You will need these components. Prices fluctuate, and so are not included here. Alternative versions can be sourced, and we welcome edits for tested alternatives.

Table 2. Table Bill Of Materials (BOM)
CountDescriptionURLNumber in Package

1

Printed Circuit Board Assembly

PCBA

1

1

2Pack Upgraded 3.5Ah M 12 Battery for Milwaukee 12V Battery Lithium XC M 12B Batteries

Battery

2

3

Washers

Should come with the board

3

3

Nuts

Should come with the board

3

Recommeded Tools

These tools are recommended. URLs are for tools purchased and used in the building of the prototypes:

Table 3. Table Tool List
DescriptionURL

A hex screwdriver for the M4 screws

Hex Screwdriver

A 10mm socket wrench

Socket wrench

Build Instructions

Building this version of the controller is more a matter of ensuring that the Controller Box was printed cleanly and all support material is properly removed.

Attach Light Panel to body (unless using fully transparent one piece body):

DSCF0367 X3
DSCF0369 X3
DSCF0370 X3

Place the printed circuit board assembly battery leads into Plate:

DSCF0372 X3
DSCF0374 X3
DSCF0375 X3

Place the printed circuit board assembly with Plate into the Body:

DSCF0377 X3
DSCF0378 X3
DSCF0381 X3

Place washer over the power port, then finger tighten a hex nut over the same power port to hold the Plate in place:

DSCF0382 X3
DSCF0385 X3
DSCF0387 X3

Put the lid onto the body:

DSCF0389 X3
DSCF0392 X3

Place washer over BNC jack, then finger tighten a hex nut over the same BNC jack:

DSCF0393 X3
DSCF0394 X3
DSCF0395 X3

Place washer over potentiometer, then finger tighten a hex nut over the same potentiometer:

DSCF0397 X3
DSCF0398 X3
DSCF0399 X3
DSCF0400 X3

Use socket wrench to tighten hex nuts into place:

DSCF0402 X3
DSCF0404 X3

Attach 2X MOLLE spacers onto MOLLE strap:

DSCF0408 X3
DSCF0411 X3

Attach and screw MOLLE strap (with spacers) onto lid with M4 screws using a hex screwdriver:

DSCF0416 X3
DSCF0417 X3
DSCF0418 X3

Attach and secure MOLLE Catch onto MOLLE Strap and Lid with M4 screws using hex screwdriver:

DSCF0420 X3
DSCF0421 X3
DSCF0423 X3
DSCF0427 X3

Attach knob onto potentiometer:

DSCF0431 X3
DSCF0432 X3

Insert m12 battery:

DSCF0435 X3

Turn knob to turn on power (it should beep and flash an LED battery level indicator):

DSCF0437 X3
DSCF0438 X3

Test m12 battery controller with fan box by attaching a BNC cable:

DSCF0440 X3

Congratulations! You have built a Tetra PAPRa M12 Controller Box v4 (August 2021)!

DSCF0443 X3